Bitumen Emulsions


We Offering Bitumen Emulsion, which are formed in compliance with standard.These Bitumen Emulsion emulsions are specially designed for ensuring a uniform and strong Tack Coat for bituminous road construction purpose. Available as Bitumen Emulsion.These products are suitable as binder for Penetration Macadam and Sand Seal.

Tack Coat Tack Coat application:

  • A light spray of Bitumen Emulsion, which may be hand or machine sprayed
  • Used to ensure a good bond between an old and a new bituminous surfacing layer
  • Applied very thin and must over the entire surface evenly
  • GRADES OF BITUMEN EMULSION
    • Rapid Set - RS-1 & RS-2
    • Medium Set - MS
    • Slow Set - SS-1 & SS-2
  • RS-1 : Tack-Coating
  • RS-2 : Surface Dressing,
  • MS : Premix carpet, Patch Repair
  • SS-1 : Priming
  • SS-2 : SDBC, BC, BM, Slurry Seal,PMB/Latex Emulsion : Micro-surfacing
...

Bitumen Emulsion R.S. - 1
Key Feature:

  • A viscous liquid emulsion with high binder content
  • Suitable for Track - Coating
  • Advantages:
  • Easy and uniform spray
  • Provides high adhesion
  • Enhances structural strength of layers
  • Prevents lateral movement of structural layers
  • Provides an impervious layer to prevent water ingress from water table below the road layers

Technical Specifications:

  • Key properties as per IS 8887: 2004

Product Applications

  • Application rate as per MORTH specifications

Bitumen Emulsion R.S. -1 is available in

  • Bulk
  • RC Drums 200 Kg
  • MS Drums 200 Kg
...

Physico-chemical Properties of Cationic Bitumen Emulsion as per IS:8887- 2004 And Our Report

S.No. Properties of Bitumen Emulsion Requirement Result.
(i) Residue on 600 micron IS sieve(% mass) 0.05 max. 0.03
(ii) Viscosity by Saybolt Furol Viscometer, seconds At 500 C 20-100 55
(iii) Coagulation of emulsion at lowtemperature Nil Nil
(iv) Storage stability after 24 hrs. , %, max. 2.0 1.68
(v) Particle charge +ve +ve
(vi) Coating ability and water resistance
(a) Coating, dry aggregates
(b) Coating after spraying water
(c) Coating, wet aggregates
(d) Coating after spraying water
- -
(vii) Stability to mixing cement, %coagulation Nil Nil
( viii) Miscibility with water (coagulation) No Coagulation No Coagulation
(ix) Test on residue :
(a) Residue by evaporation, %
(b) Penetration, 250C/100 gm/5 sec.
(c) Ductility, 270C/cm.,
(d) Solubility In Trichloroethylene, %

60 min.
80-150
50 min.
98 min.

62
108
71
99

Bitumen Emulsion R.S. - 2
Key Feature:

  • A viscous liquid emulsion with high binder content
  • Suitable for surface dressing, grouting and penetration macadam applications

Advantages:

  • Easy and uniform spray
  • Provides high adhesion
  • Enhances structural strength of layers
  • Prevents lateral movement of structural layers
  • Provides an impervious layer to prevent water ingress from water table below the road layers

Technical Specifications:

  • Key properties as per IS 8887: 2004

Product Applications:

  • Application rate as per MORTH specifications

Emulsion R. S. - 2 is available in

  • Bulk
  • RC Drums 200 Kg
  • MS Drums 200 Kg

Physico-chemical Properties of Cationic Bitumen Emulsion as per IS:8887- 2004 And Our Report.

S.No. Properties of Bitumen Emulsion Requirement Result.
(i) Residue on 600 micron IS sieve(% mass) 0.05 max. 0.03
(ii) Viscosity by Saybolt Furol Viscometer, seconds At 500 C 100-300 158
(iii) Coagulation of emulsion at low temperature Nil Nil
(iv) Storage stability after 24 hrs. , %, max. 1.0 .068
(v) Particle charge +ve +ve
(vi) Coating ability and water resistance
(a) Coating, dry aggregates
(b) Coating after spraying water
(c) Coating, wet aggregates
(d) Coating after spraying water
- -
(vii) Stability to mixing cement, %coagulation Nil Nil
( viii) Miscibility with water (coagulation) No
Coagulation--
No
Coagulation--
(ix) Test on residue :
(a) Residue by evaporation, %
(b) Penetration, 250C/100 gm/5 sec.
(c) Ductility, 270C/cm.,
(d) Solubility In Trichloroethylene, %

67 min.
80-150
50 min.
98 min.

69
119
78
99

Bitumen Emulsion M.S.

Bitumen Emulsion M.S. is specially designed water based Bitumen Emulsion with moderate viscosity and setting time range in between fast setting and slow setting Bitumen Emulsion that makes it an ideal product for premixing applications and patch repairing . It is chocolate brown in colour and is a free flowing liquid at ambient temperature. Bitumen Emulsion MS is manufactured strictly as per IS 8887 – 2004.

Advantages:

  • No Heating Require
  • Cost Efficient
  • Easy and Uniform Mix
  • Low Temperature Curing
  • Minimum Preparation Time for Surface Repair
  • Medium Setting Time
  • High Adhesive Properties
  • Stable Patch
  • Resistant to Stripping by Water
  • Environment Friendly
  • Bonds well with Cool, Damp Surfaces

Application
Emulsion M.S. is ideally suited for:

  • Pot Hole Repair/Patch work
  • 20 mm Pre-Mix Carpet

Emulsion M.S. is available in

  • Bulk
  • RC Drums 200 Kg
  • MS Drums 200 Kg

Physico-chemical Properties of Cationic Bitumen Emulsion as per IS:8887- 2004 And Our Report.

S.No. Properties of Bitumen Emulsion Requirement Result.
(i) Residue on 600 micron IS sieve(% mass) 0.05 max. 0.02
(ii) Viscosity by Saybolt Furol Viscometer, seconds At 500 C 50 - 300 64
(iii) Coagulation of emulsion at low temperature Nil Nil
(iv) Storage stability after 24 hrs. , %, max. 1.0 0.62
(v) Particle charge +ve +ve
(vi) Coating ability and water resistance
(a) Coating, dry aggregates
(b) Coating after spraying water
(c) Coating, wet aggregates
(d) Coating after spraying water

Good
Fair
Fair
Fair
Good
(vii) Stability to mixing cement, %coagulation Nil Nil
( viii) Miscibility with water (coagulation) No
Coagulation--
No
Coagulation--
(ix) Test on residue :
(a) Residue by evaporation, %
(b) Penetration, 250C/100 gm/5 sec.
(c) Ductility, 270C/cm.,
(d) Solubility In Trichloroethylene, %

65 min.
60-150
50 min.
98 min.

66
99
74
99

Bitumen Emulsion S.S.
Key Features:

  • Invert emulsion used for prime coat and fog spray

Advantages:

  • Coats and bonds loose mineral particles on the surface of the base course
  • Seals surface pores and makes the surface of the base course water-resistant
  • Penetrates the WMM surface so as to plug the capillary voids in it
  • Hardens and toughens the base course
  • Penetrates miniature pores of Sub-base
  • Compatible with ordinary portland cement

Technical Specifications:

  • Key properties as per IS 8887: 2004

Product Applications

  • Application rate as per Morth specifications

Emulsion S.S. is available in

  • Bulk
  • RC Drums 200 Kg
  • MS Drums 200 Kg

Physico-chemical Properties of Cationic Bitumen Emulsion as per IS:8887- 2004 And Our Report.

S.No. Properties of Bitumen Emulsion Requirement Result.
(i) Residue on 600 micron IS sieve(% mass) 0.05 max. 0.04
(ii) Viscosity by Saybolt Furol Viscometer, seconds At 250 C 30 - 150 68
(iii) Coagulation of emulsion at low temperature Nil Nil
(iv) Storage stability after 24 hrs. , %, max. 2.0 1.28
(v) Particle charge +ve +ve
(vi) Coating ability and water resistance
(a) Coating, dry aggregates
(b) Coating after spraying water
(c) Coating, wet aggregates
(d) Coating after spraying water
- -
(vii) Stability to mixing cement, %coagulation 2 1.05
( viii) Miscibility with water (coagulation) No
Coagulation--
No
Coagulation--
(ix) Test on residue :
(a) Residue by evaporation, %
(b) Penetration, 250C/100 gm/5 sec.
(c) Ductility, 270C/cm.,
(d) Solubility In Trichloroethylene, %

60 min.
60-120
50 min.
98 min.

62
108
72
99